ZnS:Cu电致发光电压传感器及其温度漂移补偿 -

姓名
邮箱
手机号码
标题
留言内容
验证码

ZnS:Cu电致发光电压传感器及其温度漂移补偿

doi:10.3788/CO.20171004.0514

1.
北京航空航天大学仪器科学与光电工程学院光电工程系, 北京 100191
2.
上海科润光电技术有限公司, 上海 201619

详细信息

作者简介:
李长胜(1967-), 男, 河北青龙人, 博士, 副教授, 2003年于日本群马大学获得博士学位, 主要从事物理光学、光学传感与器件、光通信等方面的研究

通讯作者:
李长胜, E-mail:cli@buaa.edu.cn

中图分类号:TN383;TM835.1
计量
- 文章访问数:1436
- HTML全文浏览量:415
- PDF下载量:747
- 被引次数:0
出版历程
- 收稿日期:2016-12-26
- 修回日期:2017-01-08
- 刊出日期:2017-08-01

ZnS:Cu electroluminescent voltage sensor and its temperature drift compensation

1.
Department of Optoelectronics Engineering, School of Instrumentation Science and Optoelectronics Engineering, Beihang University, Beijing 100191, China
2.
Shanghai Kerun Phospher Technology Co. Ltd., Shanghai 201619, China

More Information

Corresponding author:LI Chang-sheng, E-mail:cli@buaa.edu.cn

摘要

摘要:利用ZnS：Cu电致发光粉末与环氧树脂胶混合，设计制作了一种梯形电极结构的电压传感单元，实现了电致发光电压传感器输出信号的温度漂移补偿。电致发光电压传感信号通过2根塑料光纤传输到2个硅光电探测器，并选择其开路电压作为传感器的输出信号。在同一外加电压条件下，梯形电极区域内的电场分布是不均匀的，因而不同场点的发光亮度不同。通过测量梯形电极区域内2个不同发光点的发光强度随外加电压的变化，并对两路输出电压传感信号进行数据拟合与计算，可获知被测电压的有效值，并可实现对输出信号温度漂移的补偿。在-40~60℃范围内，采用上述温度漂移补偿方法测量了有效值在0.7~1.5 kV范围内的工频电压，传感器输出信号的非线性误差低于1.6%，验证了该温度漂移补偿方法的有效性。
- 光学电压传感器/
- 电致发光效应/
- 高电压测量/
- 温度漂移补偿
Abstract:A ladder-shaped voltage sensing unit is designed and fabricated using ZnS:Cu powder and epoxy adhesive, and the temperature drift compensation of an electroluminescent voltage sensing signal is implemented. Two channels of electroluminescent voltage sensing signals are transmitted to two photo-detectors using two pieces of plastic optical fibers. Open circuit voltages of the two photo-detectors are used as output voltage sensing signals. The electric field distribution is non-uniform within the ladder-shaped electroluminescent voltage sensing unit, and thus the electroluminescent brightness is also non-uniform under a same applied voltage. AC voltage sensing signals can be obtained by measuring the electroluminescent brightness at two different positions on the ladder-shaped voltage sensing unit. The temperature drift compensation existing in output voltage sensing signal can be achieved by an optimal calculation and fitting of experimental data. 50 Hz AC voltage in the range of 0.7-1.5 kV is measured, and the nonlinear error is less than 1.6% in the range of -40-60℃. This result demonstrates the effectiveness of the proposed temperature drift compensation method.
- optical voltage sensor/
- electroluminescent effect/
- high voltage measurement/
- temperature drift compensation

HTML全文

图 1基于ZnS\:Cu粉末的电致发光电压传感单元结构示意图

Figure 1.Structure diagram of electroluminescent voltage sensing unit based on ZnS\:Cu powder

下载: 全尺寸图片幻灯片

图 2电致发光电压传感特性的实验装置

Figure 2.Experimental setup of electroluminescent voltage sensing performances

下载: 全尺寸图片幻灯片

图 3在不同外加电压下，梯形电压传感单元样品2的电致发光照片

Figure 3.Photographs of electroluminescence from the second ladder-shaped voltage sensing unit under different applied voltages

下载: 全尺寸图片幻灯片

图 4当U_i=1 200 V时，对应于梯形电压传感单元样品2的开路电压U_oc随不同发光场点位置x变化的曲线

Figure 4.Curves of open-circuit voltageU_ocversus different electroluminescent positions on the second ladder-shaped voltage sensing unit whenU_i=1 200 V

下载: 全尺寸图片幻灯片

图 5工频电压传感信号波形

Figure 5.Waveforms of electroluminescent voltage sensing signals of 50 Hz AC voltage

下载: 全尺寸图片幻灯片

图 6开路电压U_oc1和U_oc2随外加电压有效值U_i变化的曲线

Figure 6.Curves of open circuit voltageU_oc1andU_oc2versus applied voltageU_i

下载: 全尺寸图片幻灯片

图 7梯形电压传感单元的输入阻抗随外加电压变化的曲线

Figure 7.Curves of input impedanceZ_iof ladder-shaped voltage sensing unit versus applied voltage

下载: 全尺寸图片幻灯片

图 8开路电压与被测电压及温度的关系

Figure 8.Open circuit voltage versus applied voltage and temperature

下载: 全尺寸图片幻灯片

图 9当U_i=1 200 V时开路电压随温度变化的曲线

Figure 9.Curves of open circuit voltage versus temperature under the condition ofU_i=1 200 V

下载: 全尺寸图片幻灯片

图 10U_i=1 200 V时，输出电压在补偿前(U_oc1和U_oc2)和补偿后(U_om)随温度变化的曲线

Figure 10.Curves of output voltages versus temperature without compensation (U_oc1andU_oc2) and with compensation (U_om) under the condition ofU_i=1 200 V

下载: 全尺寸图片幻灯片

图 11温度漂移补偿后传感器输出电压U_om随外加电压U_i的实验数据及线性拟合直线

Figure 11.Experimental data of output voltageU_omwith temperature compensation and applied voltagesU_i, and their linear fitting line

下载: 全尺寸图片幻灯片

图 12U_i=1 200 V时，输入阻抗与温度的关系

Figure 12.Relationship of input impedance and temperature under the condition ofU_i=1 200 V

下载: 全尺寸图片幻灯片

参考文献 (16)

[1]	LI CH SH. Optical voltage sensors:principle, problem and research proposal[J]. SPIE, 2016, 10158, 2016:101581N.
[2]	谢施君, 汪海, 曾嵘, 等.基于集成光学电场传感器的过电压测量技术[J].高电压技术, 2016, 42(9):2929-2935.http://www.cnki.com.cn/Article/CJFDTOTAL-GDYJ201609033.htm XIE SH J, WANG H, ZENG R, Overvoltage Measurement technique based on integrated optical electric field sensor[J]. High Voltage Engineering, 2016, 42(9):2929-2935. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-GDYJ201609033.htm
[3]	李长胜, 王伟岐.基于电致发光效应的光学电压传感器[J].中国光学, 2016, 9(1):30-40.//www.illord.com/CN/abstract/abstract9385.shtml LI CH SH, WANG W Q. Review of optical voltage sensor based on electroluminescent effect[J]. Chinese Optics, 2016, 9(1):30-40. (in Chinese)//www.illord.com/CN/abstract/abstract9385.shtml
[4]	姚健, 李长胜.利用电致发光线的光学电压有效值传感器[J].光电子· , 2013, 24(1):34-38.http://www.cnki.com.cn/Article/CJFDTOTAL-GDZJ201301008.htm YAO J, LI CH SH. Optical measurement of effective ac voltage using the electroluminescent wire[J]. Journal of Optoelectronics·Laser, 2013, 24(1):34-38. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-GDZJ201301008.htm
[5]	王伟岐, 李长胜.一种光电式电压传感器及其温度漂移补偿方法[J].光电子· , 2015, 26(9):1671-1679.http://www.cnki.com.cn/Article/CJFDTOTAL-GDZJ201509006.htm WANG W Q, LI CH SH. An optoelectronic voltage sensor and its compensation method for temperature drift[J]. Journal of Optoelectronics·Laser, 2015, 26(9):1671-1679. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-GDZJ201509006.htm
[6]	陈佳, 李长胜, 郭素文, 等. ZnS:Cu电致发光薄膜的交流电压传感特性[J]. 杂志, 2016, 37(11):6-9.http://www.cnki.com.cn/Article/CJFDTOTAL-JGZZ201611002.htm CHEN J, LI CH SH, GUO S W, et al.. AC voltage sensing performance of electroluminescent ZnS:Cu film[J]. Laser Journal, 2016, 37(11):6-9. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-JGZZ201611002.htm
[7]	毛清华, 刘军林, 全知觉, 等. p型层结构与掺杂对GaInN发光二极管正向电压温度特性的影响[J].物理学报, 2015, 64(10):107801.doi:10.7498/aps.64.107801 MAO Q H, LIU J L, QUAN ZH J, et al.. Influences of p-type layer structure and doping profile on the temperature dependence of the forward voltage characteristic of GaInN light-emitting diode[J]. Acta Physica Sinica, 2015, 64(10):107801. (in Chinese)doi:10.7498/aps.64.107801
[8]	徐叙瑢, 苏勉曾.发光学与发光材料[M].北京:化学工业出版社, 2004:388-425. XU X R, SU M Z. Luminescence and Luminescent Materials[M]. Beijing:Chemical Industry Press, 2004:388-425. (in Chinese)
[9]	钟国柱. Ⅱ-Ⅵ族化合物薄膜电致发光[J].发光学报, 2006, 27(1):6-17.http://www.cnki.com.cn/Article/CJFDTOTAL-FGXB200601002.htm ZHONG G ZH. Thin film electroluminescence in Ⅱ-Ⅵ compounds[J]. Chinese Journal of Luminescence, 2006, 27(1):6-17. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-FGXB200601002.htm
[10]	许少辉, 周雅伟, 赵晓鹏.无机粉末电致发光材料的研究进展[J].材料导报, 2007, 21:162-166.http://www.cnki.com.cn/Article/CJFDTOTAL-CLDB2007S3048.htm XU SH H, ZHOU Y W, ZHAO X P. Research and development of inorganic powder EL materials[J]. Materials Review, 2007, 21:162-166. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-CLDB2007S3048.htm
[11]	徐家跃.发光材料及其新进展[J].无机材料学报, 2016, 31(10):1009-1012.http://www.cnki.com.cn/Article/CJFDTOTAL-WGCL201610001.htm XU J Y.Recent developments of luminescent materials[J]. Journal of Inorganic Materials, 2016, 31(10):1009-1012. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-WGCL201610001.htm
[12]	刘泽明, 徐建萍, 李霖霖, 等.聚合物/碳量子点复合EL器件及光谱移动机理[J].发光学报, 2016, 37(7):823-828.http://www.cnki.com.cn/Article/CJFDTOTAL-FGXB201607022.htm LIU Z M, XU J P, LI L L, et al. Polymer/Carbon quantum dots composite EL devices and tunable spectra mechanism[J]. Chinese Journal of Luminescence, 2016, 37(7):823-828. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-FGXB201607022.htm
[13]	赵辉, 侯延冰, 何大伟, 等. ZnS:Cu的电致发光特性[J].北方交通大学学报, 2001, 25(3):67-69.http://www.cnki.com.cn/Article/CJFDTOTAL-JGZZ201611002.htm ZHAO H, HOU Y B, HE D W, et al.. Electroluminescent characters of ZnS:Cu[J]. Journal of Northern Jiaotong University, 2001, 25(3):67-69. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-JGZZ201611002.htm
[14]	王辉, 孟令国, 梁志虎, 等. ZnS:Cu粉末交流电致发光器件特性研究[J].真空电子技术, 2008(6):1-4.http://www.cnki.com.cn/Article/CJFDTOTAL-ZKDJ200806004.htm WANG H, MENG L G, LIANG ZH H. An investigation on ac electroluminescent properties of ZnS:Cu powder[J]. Vacuum Electronics, 2008(6):1-4. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-ZKDJ200806004.htm
[15]	HAYT W H, BUCK J A. Engineering Electromagnetics[M]. Beijing:Tsinghua University Press, 2009.
[16]	庄哲民, 黄惟一, 刘少强.提高传感器精度的神经网络方法[J].计量学报, 2002, 23(1):78-80.http://www.cnki.com.cn/Article/CJFDTOTAL-JLXB200201019.htm ZHUANG ZH M, HUANG W Y, LIU SH Q. Transducer accuracy enhancement using neural networks[J]. Acta Metrological Sinica, 2002, 23(1):78-80. (in Chinese)http://www.cnki.com.cn/Article/CJFDTOTAL-JLXB200201019.htm