Citation: | WU Di, WANG Xu-yue. Melt particles morphology during laser cutting zirconia ceramic[J].Chinese Optics, 2016, 9(5): 554-562.doi:10.3788/CO.20160905.0554 |
[1] |
SAMANT A N, DAHOTRE N B.Laser machining of structural ceramics-a review[J].J.European Ceramic Society, 2009, 29(6):969-993.
doi:10.1016/j.jeurceramsoc.2008.11.010
|
[2] |
WEE L M, CROUSE P L, LI L.A statistical analysis of striation formation during laser cutting of ceramics[J].Int.J.Adv.Manuf.Technol., 2008, 36:699-706.
doi:10.1007/s00170-006-0888-5
|
[3] |
徐斌, 伍晓宇, 罗烽, 等.0Cr18Ni9不锈钢箔的飞秒 烧蚀[J].光学精密工程, 2012, 20(1):45-51.
doi:10.3788/OPE.
XU B, WU X Y, LUO F, et al..Ablation of 0Cr18Ni9 stainless steel films by femtosecond laser[J].Opt.Precision Eng., 2012, 20(1):45-51.(in Chinese)
doi:10.3788/OPE.
|
[4] |
徐斌, 伍晓宇, 凌世全, 等.飞秒 切割与微细电阻滑焊组合制备三维金属微结构[J].光学精密工程, 2012, 20(8):1811-1823.
doi:10.3788/OPE.
XU B, WU X Y, LING SH Q, et al..Fabrication of 3D metal micro-structure based on fs laser cutting and micro electric resistance slip welding[J].Opt.Precision Eng., 2012, 20(8):1811-1823.(in Chinese)
doi:10.3788/OPE.
|
[5] |
孟庆轩, 王续跃, 徐文骥, 等.薄板 切割气熔比数学建模及试验验证[J].机械工程学报, 2011, 47(17):172-178.
doi:10.3901/JME.2011.17.172
MENG Q X, WANG X Y, XU W J, et al..Vaporization-melt ratio mathematical model and experiments of laser cutting sheet metal[J].J.Mechanical Engineering, 2011, 47(17):172-178.(in Chinese)
doi:10.3901/JME.2011.17.172
|
[6] |
王续跃, 孟庆轩, 康仁科, 等.气熔比法铝合金薄板 切割试验研究[J].中国 , 2010, 37(10):2648-2652.
doi:10.3788/CJL
WANG X Y, MENG Q X, KANG R K, et al..Experiments of laser cutting of aluminum alloy sheet based on vaporization-melt ratio controlled method[J].Chinese J.Lasers, 2010, 37(10):2648-2652.(in Chinese)
doi:10.3788/CJL
|
[7] |
DABBY F W.High-intensity laser induced vaporizationand explosion of solid material[J].Quantum Electron, 1972, 8(2):106-111.
doi:10.1109/JQE.1972.1076937
|
[8] |
QUINTERO F, VARAS F, POU J, et al..Theoretical analysis of material removal mechanisms in pulsed laser fusion cutting of ceramics[J].J.Physics D:Applied Physics, 2005, 38(4):655-666.
doi:10.1088/0022-3727/38/4/021
|
[9] |
LOBO L, WILLIAM K, TYRER J R.The effect of laser processing parameters on the particulate generated during the cutting of thin mild steel sheet[J].J.Mech.Engng.Sci., 2002, 216(3):301-313.
doi:10.1243/0954406021525016
|
[10] |
SCHULZ W.Dynamics of ripple formation and melt flow in laser beam cutting[J].J.Physics D:Applied Physics, 1999, 32:1219-1228.
doi:10.1088/0022-3727/32/11/307
|
[11] |
CABANILLASE E D, CREUS M F, MERCADER R C.Microscopic spheroidal particles obtained by laser cutting[J].J.Mater.Sci., 2005, 40(2):519-522.
doi:10.1007/s10853-005-6118-y
|
[12] |
YILBAS B S, ABDUL ALEEM B J.Dross formation during laser cutting process[J].J.Physics D:Applied Physics, 2006, 39(7):1451-1461.
doi:10.1088/0022-3727/39/7/017
|
[13] |
黄开金, 谢长生, 邵可然. 切割1Crl8Ni9Ti不锈钢管材挂渣和飞渣的研究[J].应用 , 2001, 21(3):301-313.
http://www.cnki.com.cn/Article/CJFDTOTAL-YYJG200103003.htm
HUANG K J, XIE C S, SHAO K R.Investigation on the hanging dross and the flight slag of 1Crl8Ni9Ti stainless steel pipe laser cutting[J].Applied Laser, 2001, 21(3):159-163.(in Chinese)
http://www.cnki.com.cn/Article/CJFDTOTAL-YYJG200103003.htm
|
[14] |
王彦飞, 王续跃, 徐文骥, 等.基于去除熔化物形态分析的铝合金薄板 切割试验研究[J].中国 , 2012, 39(8):0803007.
doi:10.3788/CJL
WANG Y F, WANG X Y, XU W J, et al..Experimental study on laser cutting based on removal forms for aluminum alloy sheet[J].Chinese J.Lasers, 2012, 39(8):0803007.(in Chinese)
doi:10.3788/CJL
|
[15] |
王彦飞, 王续跃, 徐文骥, 等.基于图像处理的铝合金薄板 切割质量研究[J].中国 , 2014, 41(1):0103002.
doi:10.3788/CJL
WAND Y F, WANG X Y, XU W J, et al..Study on laser cutting quality of aluminum alloy sheet based on imagine processing[J].Chinese J.Lasers, 2014, 41(1):0103002.(in Chinese)
doi:10.3788/CJL
|
[16] |
RIVEIRO A, UINTERO F, LUSQUINOS F, et al..Study of melt flow dynamics and influence on quality for CO
2laser fusion cutting[J].J.Physics D:Applied Physics, 2011, 44(13):135501.
doi:10.1088/0022-3727/44/13/135501
|